[ Upstream commit e7ede72a6d40cb3a30c087142d79381ca8a31dab ]
The current symbols__fixup_end() heuristic for the last entry in the rb
tree is suboptimal as it leads to not being able to recognize the symbol
in the call graph in a couple of corner cases, for example:
i) If the symbol has a start address (f.e. exposed via kallsyms)
that is at a page boundary, then the roundup(curr->start, 4096)
for the last entry will result in curr->start == curr->end with
a symbol length of zero.
ii) If the symbol has a start address that is shortly before a page
boundary, then also here, curr->end - curr->start will just be
very few bytes, where it's unrealistic that we could perform a
match against.
Instead, change the heuristic to roundup(curr->start, 4096) + 4096, so
that we can catch such corner cases and have a better chance to find
that specific symbol. It's still just best effort as the real end of the
symbol is unknown to us (and could even be at a larger offset than the
current range), but better than the current situation.
Alexei reported that he recently run into case i) with a JITed eBPF
program (these are all page aligned) as the last symbol which wasn't
properly shown in the call graph (while other eBPF program symbols in
the rb tree were displayed correctly). Since this is a generic issue,
lets try to improve the heuristic a bit.
Reported-and-Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: 2e538c4a18 ("perf tools: Improve kernel/modules symbol lookup")
Link: http://lkml.kernel.org/r/bb5c80d27743be6f12afc68405f1956a330e1bc9.1489614365.git.daniel@iogearbox.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22905582f6dd4bbd0c370fe5732c607452010c04 ]
Command perf test -v 16 (Setup struct perf_event_attr test) always
reports success even if the test case fails. It works correctly if you
also specify -F (for don't fork).
root@s35lp76 perf]# ./perf test -v 16
15: Setup struct perf_event_attr :
--- start ---
running './tests/attr/test-record-no-delay'
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB /tmp/tmp4E1h7R/perf.data
(1 samples) ]
expected task=0, got 1
expected precise_ip=0, got 3
expected wakeup_events=1, got 0
FAILED './tests/attr/test-record-no-delay' - match failure
test child finished with 0
---- end ----
Setup struct perf_event_attr: Ok
The reason for the wrong error reporting is the return value of the
system() library call. It is called in run_dir() file tests/attr.c and
returns the exit status, in above case 0xff00.
This value is given as parameter to the exit() function which can only
handle values 0-0xff.
The child process terminates with exit value of 0 and the parent does
not detect any error.
This patch corrects the error reporting and prints the correct test
result.
Signed-off-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
LPU-Reference: 20170913081209.39570-2-tmricht@linux.vnet.ibm.com
Link: http://lkml.kernel.org/n/tip-rdube6rfcjsr1nzue72c7lqn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eebc509b20881b92d62e317b2c073e57c5f200f0 upstream.
Fix --funcs (-F) option to show correct symbols for offline module.
Since previous perf-probe uses machine__findnew_module_map() for offline
module, even if user passes a module file (with full path) which is for
other architecture, perf-probe always tries to load symbol map for
current kernel module.
This fix uses dso__new_map() to load the map from given binary as same
as a map for user applications.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148350053478.19001.15435255244512631545.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f2ed153b916c95a49a1ca9d7107738664224b7f ]
Since 'perf probe' supports cross-arch probes, it is possible to analyze
different arch kernel image which has different bits-per-long.
In that case, it fails to get the module name because it uses the
MOD_NAME_OFFSET macro based on the host machine bits-per-long, instead
of the target arch bits-per-long.
This fixes above issue by changing modname-offset based on the target
archs bit width. This is ok because linux kernel uses LP64 model on
64bit arch.
E.g. without this (on x86_64, and target module is arm32):
$ perf probe -m build-arm/fs/configfs/configfs.ko -D configfs_lookup
p:probe/configfs_lookup :configfs_lookup+0
^-Here is an empty module name.
With this fix, you can see correct module name:
$ perf probe -m build-arm/fs/configfs/configfs.ko -D configfs_lookup
p:probe/configfs_lookup configfs:configfs_lookup+0
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148337043836.6752.383495516397005695.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee14ac0ef6827cd6f9a572cc83dd0191ea17812c upstream.
Intel PT uses IP compression based on the last IP. For decoding
purposes, 'last IP' is considered to be reset to zero whenever there is
a synchronization packet (PSB). The decoder wasn't doing that, and was
treating the zero value to mean that there was no last IP, whereas
compression can be done against the zero value. Fix by setting last_ip
to zero when a PSB is received and keep track of have_last_ip.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1495786658-18063-6-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f04d98e972b59706bd43d6cc75efac91f8fba50 upstream.
The decoder uses its current timestamp in samples. Usually that is a
timestamp that has already passed, but in some cases it is a timestamp
for a branch that the decoder is walking towards, and consequently
hasn't reached. Improve that situation by using the pkt_state to
determine when to use the current or previous timestamp.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1495786658-18063-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a937a25a7e3c19d5fb3f9d92f605cf5fda219d8 upstream.
Fix perf-probe to show probe definition on gcc generated symbols for
offline kernel (including cross-arch kernel image).
gcc sometimes optimizes functions and generate new symbols with suffixes
such as ".constprop.N" or ".isra.N" etc. Since those symbol names are
not recorded in DWARF, we have to find correct generated symbols from
offline ELF binary to probe on it (kallsyms doesn't correct it). For
online kernel or uprobes we don't need it because those are rebased on
_text, or a section relative address.
E.g. Without this:
$ perf probe -k build-arm/vmlinux -F __slab_alloc*
__slab_alloc.constprop.9
$ perf probe -k build-arm/vmlinux -D __slab_alloc
p:probe/__slab_alloc __slab_alloc+0
If you put above definition on target machine, it should fail
because there is no __slab_alloc in kallsyms.
With this fix, perf probe shows correct probe definition on
__slab_alloc.constprop.9:
$ perf probe -k build-arm/vmlinux -D __slab_alloc
p:probe/__slab_alloc __slab_alloc.constprop.9+0
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148350060434.19001.11864836288580083501.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7dd112ea5cacf91ae72c0714c3b911eb6016fea upstream.
Fix below compile error:
CC util/scripting-engines/trace-event-perl.o
In file included from /usr/lib/perl5/5.22.2/i686-linux/CORE/perl.h:5673:0,
from util/scripting-engines/trace-event-perl.c:31:
/usr/lib/perl5/5.22.2/i686-linux/CORE/inline.h: In function 'S__is_utf8_char_slow':
/usr/lib/perl5/5.22.2/i686-linux/CORE/inline.h:270:5: error: nested extern declaration of 'Perl___notused' [-Werror=nested-externs]
dTHX; /* The function called below requires thread context */
^
cc1: all warnings being treated as errors
After digging perl5 repository, I find out that we will meet this
compile error with perl from v5.21.1 to v5.25.4
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170212024655.GA15997@udknight
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8434a2ec13d5c8cb25716950bfbf7c9d7b64628a upstream.
In commit daeecbc0c4 ("perf tools: Add event_update event scale type"), the
handling of PERF_EVENT_UPDATE__SCALE cast struct event_update_event->data to a
pointer to event_update_event_scale, uses some field from this casted struct
and then ends up falling through to the handling of another event type,
PERF_EVENT_UPDATE__CPUS were it casts that ev->data to yet another type, oops,
fix it by inserting the missing break.
Noticed when building perf using gcc 7 on Fedora Rawhide:
util/header.c: In function 'perf_event__process_event_update':
util/header.c:3207:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
evsel->scale = ev_scale->scale;
~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~
util/header.c:3208:2: note: here
case PERF_EVENT_UPDATE__CPUS:
^~~~
This wasn't noticed because probably PERF_EVENT_UPDATE__CPUS comes after
PERF_EVENT_UPDATE__SCALE, so we would just create a bogus evsel->own_cpus when
processing a PERF_EVENT_UPDATE__SCALE to then leak it and create a new cpu map
with the correct data.
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: daeecbc0c4 ("perf tools: Add event_update event scale type")
Link: http://lkml.kernel.org/n/tip-lukcf9hdj092ax2914ss95at@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aff8ba0a4c9c9191bb788171a1c54778e1246a2 upstream.
Addressing this warning from gcc 7:
CC /tmp/build/perf/bench/numa.o
bench/numa.c: In function '__bench_numa':
bench/numa.c:1582:42: error: '%d' directive output may be truncated writing between 1 and 10 bytes into a region of size between 8 and 17 [-Werror=format-truncation=]
snprintf(tname, 32, "process%d:thread%d", p, t);
^~
bench/numa.c:1582:25: note: directive argument in the range [0, 2147483647]
snprintf(tname, 32, "process%d:thread%d", p, t);
^~~~~~~~~~~~~~~~~~~~
In file included from /usr/include/stdio.h:939:0,
from bench/../util/util.h:47,
from bench/../builtin.h:4,
from bench/numa.c:11:
/usr/include/bits/stdio2.h:64:10: note: '__builtin___snprintf_chk' output between 17 and 35 bytes into a destination of size 32
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-twa37vsfqcie5gwpqwnjuuz9@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e2bbc039fad9eabad6c4c1a473c8b2554cdd2d4 upstream.
Addressing a few cases spotted by a new warning in gcc 7:
tests/parse-events.c: In function 'test_pmu_events':
tests/parse-events.c:1790:39: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 90 [-Werror=format-truncation=]
snprintf(name, MAX_NAME, "cpu/event=%s/u", ent->d_name);
^~
In file included from /usr/include/stdio.h:939:0,
from /git/linux/tools/perf/util/map.h:9,
from /git/linux/tools/perf/util/symbol.h:7,
from /git/linux/tools/perf/util/evsel.h:10,
from tests/parse-events.c:3:
/usr/include/bits/stdio2.h:64:10: note: '__builtin___snprintf_chk' output between 13 and 268 bytes into a destination of size 100
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tests/parse-events.c:1798:29: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 100 [-Werror=format-truncation=]
snprintf(name, MAX_NAME, "%s:u,cpu/event=%s/u", ent->d_name, ent->d_name);
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 945aea220b ("perf tests: Move test objects into 'tests' directory")
Link: http://lkml.kernel.org/n/tip-ty4q2p8zp1dp3mskvubxskm5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ea6856d6f5629d742edc23b8b76e6263371ef45 upstream.
To address new warnings emmited by gcc 7, e.g.::
CC /tmp/build/perf/util/intel-pt-decoder/intel-pt-pkt-decoder.o
CC /tmp/build/perf/tests/parse-events.o
util/intel-pt-decoder/intel-pt-pkt-decoder.c: In function 'intel_pt_pkt_desc':
util/intel-pt-decoder/intel-pt-pkt-decoder.c:499:6: error: this statement may fall through [-Werror=implicit-fallthrough=]
if (!(packet->count))
^
util/intel-pt-decoder/intel-pt-pkt-decoder.c:501:2: note: here
case INTEL_PT_CYC:
^~~~
CC /tmp/build/perf/util/intel-pt-decoder/intel-pt-decoder.o
cc1: all warnings being treated as errors
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-mf0hw789pu9x855us5l32c83@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdf23a9a190d7ecea092fd5c4aabb7d4bd0a9980 upstream.
The size of dirent->dt_name is NAME_MAX + 1, but the size for the 'path'
buffer is hard coded at 256, which may truncate it because we also
prepend "/proc/", so that all that into account and thank gcc 7 for this
warning:
/git/linux/tools/perf/util/thread_map.c: In function 'thread_map__new_by_uid':
/git/linux/tools/perf/util/thread_map.c:119:39: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size 250 [-Werror=format-truncation=]
snprintf(path, sizeof(path), "/proc/%s", dirent->d_name);
^~
In file included from /usr/include/stdio.h:939:0,
from /git/linux/tools/perf/util/thread_map.c:5:
/usr/include/bits/stdio2.h:64:10: note: '__builtin___snprintf_chk' output between 7 and 262 bytes into a destination of size 256
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-csy0r8zrvz5efccgd4k12c82@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 613f050d68a8ed3c0b18b9568698908ef7bbc1f7 ]
Fix to probe on gcc generated functions on modules. Since
probing on a module is based on its symbol name, it should
be adjusted on actual symbols.
E.g. without this fix, perf probe shows probe definition
on non-exist symbol as below.
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -F in_range*
in_range.isra.12
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -D in_range
p:probe/in_range nf_nat:in_range+0
With this fix, perf probe correctly shows a probe on
gcc-generated symbol.
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -D in_range
p:probe/in_range nf_nat:in_range.isra.12+0
This also fixes same problem on online module as below.
$ perf probe -m i915 -D assert_plane
p:probe/assert_plane i915:assert_plane.constprop.134+0
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411450673.9978.14905987549651656075.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2d4edbebe07ddb77980656abe7b9bc7a9e0cdf7 ]
Fix to show correct locations for events on modules by relocating given
address instead of retrying after failure.
This happens when the module text size is big enough, bigger than
sh_addr, because the original code retries with given address + sh_addr
if it failed to find CU DIE at the given address.
Any address smaller than sh_addr always fails and it retries with the
correct address, but addresses bigger than sh_addr will get a CU DIE
which is on the given address (not adjusted by sh_addr).
In my environment(x86-64), the sh_addr of ".text" section is 0x10030.
Since i915 is a huge kernel module, we can see this issue as below.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | sort | head -n1
ffffffffc0270000 t i915_switcheroo_can_switch [i915]
ffffffffc0270000 + 0x10030 = ffffffffc0280030, so we'll check
symbols cross this boundary.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | grep -B1 ^ffffffffc028\
| head -n 2
ffffffffc027ff80 t haswell_init_clock_gating [i915]
ffffffffc0280110 t valleyview_init_clock_gating [i915]
So setup probes on both function and see what happen.
$ sudo ./perf probe -m i915 -a haswell_init_clock_gating \
-a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on i915_vga_set_decode:4@gpu/drm/i915/i915_drv.c in i915)
As you can see, haswell_init_clock_gating is correctly shown,
but valleyview_init_clock_gating is not.
With this patch, both events are shown correctly.
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
Committer notes:
In my case:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on i915_getparam+432@gpu/drm/i915/i915_drv.c in i915)
probe:valleyview_init_clock_gating (on __i915_printk+240@gpu/drm/i915/i915_drv.c in i915)
#
# readelf -SW /lib/modules/4.9.0+/build/vmlinux | egrep -w '.text|Name'
[Nr] Name Type Address Off Size ES Flg Lk Inf Al
[ 1] .text PROGBITS ffffffff81000000 200000 822fd3 00 AX 0 0 4096
#
So both are b0rked, now with the fix:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
#
Both looks correct.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411436777.9978.1440275861947194930.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa33b9b9a2ebb00d33c83a5312d4fbf2d5aeba36 upstream.
If dso__load_kcore frees all of the existing maps, but one has already
been attached to a callchain cursor node, then we can get a SIGSEGV in
any function that happens to try to use this invalid cursor. Use the
existing map refcount mechanism to forestall cleanup of a map until the
cursor iterates past the node.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 84c2cafa28 ("perf tools: Reference count struct map")
Link: http://lkml.kernel.org/r/20170106062331.GB2707@templeofstupid.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8381cdd0e32dd748bd34ca3ace476949948bd793 upstream.
The -o/--order option is to select column number to sort a diff result.
It does the job by adding a hpp field at the beginning of the sort list.
But it should not be added to the output field list as it has no
callbacks required by a output field.
During the setup_sorting(), the perf_hpp__setup_output_field() appends
the given sort keys to the output field if it's not there already.
Originally it was checked by fmt->list being non-empty. But commit
3f931f2c42 ("perf hists: Make hpp setup function generic") changed it
to check the ->equal callback.
Anyways, we don't need to add the pseudo hpp field to the output field
list since it won't be used for output. So just skip fields if they
have no ->color or ->entry callbacks.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: 3f931f2c42 ("perf hists: Make hpp setup function generic")
Link: http://lkml.kernel.org/r/20170118051457.30946-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1c9f97f0b64e6337d9cfcc08c134450934fdd90 upstream.
Commit 21e6d84286 ("perf diff: Use perf_hpp__register_sort_field
interface") changed list_add() to perf_hpp__register_sort_field().
This resulted in a behavior change since the field was added to the tail
instead of the head. So the -o option is mostly ignored due to its
order in the list.
This patch fixes it by adding perf_hpp__prepend_sort_field().
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: 21e6d84286 ("perf diff: Use perf_hpp__register_sort_field interface")
Link: http://lkml.kernel.org/r/20170118051457.30946-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 621cb4e7837e39d25a5af5a785ad282cdd2b4ce8 upstream.
This patch modifies the build dependencies on the jitdump support in
perf. As it stands jitdump was wrongfully made dependent 100% on using
DWARF. However, the dwarf dependency, only exist if generating the
source line table in genelf_debug.c. The rest of the support does not
need DWARF.
This patch removes the dependency on DWARF for the entire jitdump
support. It keeps it only for the genelf_debug.c support.
Signed-off-by: Maciej Debski <maciejd@google.com>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-3-git-send-email-eranian@google.com
Fixes: e12b202f8f ("perf jitdump: Build only on supported archs")
[ Make it build only if NO_LIBELF isn't defined, as jitdump.o will only be built in that case ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c56cb33b56c13493eeb95612f80e4dd6e35cd109 upstream.
Since 841e3558b2 ("perf callchain: Recording 'dwarf' callchains do not
need DWARF unwinding support"), --call-graph dwarf is allowed in 'perf
record' even without unwind support. A couple of other places don't
reflect this yet though: the help text should list dwarf as a valid
record mode and the dump_size config should be respected too.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Cc: He Kuang <hekuang@huawei.com>
Fixes: 841e3558b2 ("perf callchain: Recording 'dwarf' callchains do not need DWARF unwinding support")
Link: http://lkml.kernel.org/r/1470837148-7642-1-git-send-email-rabin.vincent@axis.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed6c166cc7dc329736cace3affd2df984fb22ec8 upstream.
Fixes a perf diff regression issue which was introduced by commit
5baecbcd9c ("perf symbols: we can now read separate debug-info files
based on a build ID")
The binary name could be same when perf diff different binaries. Build
id is used to distinguish between them.
However, the previous patch assumes the same binary name has same build
id. So it overwrites the build id according to the binary name,
regardless of whether the build id is set or not.
Check the has_build_id in dso__load. If the build id is already set, use
it.
Before the fix:
$ perf diff 1.perf.data 2.perf.data
# Event 'cycles'
#
# Baseline Delta Shared Object Symbol
# ........ ....... ................ .............................
#
99.83% -99.80% tchain_edit [.] f2
0.12% +99.81% tchain_edit [.] f3
0.02% -0.01% [ixgbe] [k] ixgbe_read_reg
After the fix:
$ perf diff 1.perf.data 2.perf.data
# Event 'cycles'
#
# Baseline Delta Shared Object Symbol
# ........ ....... ................ .............................
#
99.83% +0.10% tchain_edit [.] f3
0.12% -0.08% tchain_edit [.] f2
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
CC: Dima Kogan <dima@secretsauce.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 5baecbcd9c ("perf symbols: we can now read separate debug-info files based on a build ID")
Link: http://lkml.kernel.org/r/1481642984-13593-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecf1e2253ea79c6204f4d6a5e756e8fb4aed5a7e upstream.
Instead of the one when another syscall takes place while another is being
processed (in another CPU, but we show it serialized, so need to "interrupt"
the other), and also when finally showing the sys_enter + sys_exit + duration,
where we were showing the sample->time for the sys_exit, duh.
Before:
# perf trace sleep 1
<SNIP>
0.373 ( 0.001 ms): close(fd: 3 ) = 0
1000.626 (1000.211 ms): nanosleep(rqtp: 0x7ffd6ddddfb0) = 0
1000.653 ( 0.003 ms): close(fd: 1 ) = 0
1000.657 ( 0.002 ms): close(fd: 2 ) = 0
1000.667 ( 0.000 ms): exit_group( )
#
After:
# perf trace sleep 1
<SNIP>
0.336 ( 0.001 ms): close(fd: 3 ) = 0
0.373 (1000.086 ms): nanosleep(rqtp: 0x7ffe303e9550) = 0
1000.481 ( 0.002 ms): close(fd: 1 ) = 0
1000.485 ( 0.001 ms): close(fd: 2 ) = 0
1000.494 ( 0.000 ms): exit_group( )
[root@jouet linux]#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-ecbzgmu2ni6glc6zkw8p1zmx@git.kernel.org
Fixes: 752fde44fd ("perf trace: Support interrupted syscalls")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Markus reported that there's a weird behavior on perf top --hierarchy
regarding the column length.
Looking at the code, I found a dubious code which affects the symptoms.
When --hierarchy option is used, the last column length might be
inaccurate since it skips to update the length on leaf entries.
I cannot remember why it did and looks like a leftover from previous
version during the development.
Anyway, updating the column length often is not harmful. So let's move
the code out.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 1a3906a7e6 ("perf hists: Resort hist entries with hierarchy")
Link: http://lkml.kernel.org/r/20161108130833.9263-5-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When horizontal scrolling is used in hierarchy mode, the folded signed
disappears at the right most column.
Committer note:
To test it, run 'perf top --hierarchy, see the '+' symbol at the first
column, then press the right arrow key, the '+' symbol will disappear,
this patch fixes that.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161108130833.9263-3-namhyung@kernel.org
[ Move 'width -= 2' invariant to right after the if/else ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The perf report/top on TUI supports horizontal scrolling using LEFT and
RIGHT keys.
But it calculate the number of columns incorrectly when hierarchy mode
is enabled so that keep pressing RIGHT key can make the output
disappeared.
In the hierarchy mode, all sort keys are collapsed into a single column,
so it needs to be applied when calculating column numbers.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161024162110.17918-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When building on Ubuntu 16.04, I get the following error:
Makefile:49: *** the openjdk development package appears to me missing, install and try again. Stop.
The problem is that update-java-alternatives has multiple spaces between
fields, and cut treats each space as a new delimiter:
java-1.8.0-openjdk-ppc64el 1081 /usr/lib/jvm/java-1.8.0-openjdk-ppc64el
Fix this by using awk, which handles this fine.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476325243-15788-1-git-send-email-anton@ozlabs.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch helps with Sukadev's vendor event tree where such events can happen.
>From Andi Kleen:
Any event including a .c/.o/.bpf currently triggers BPF compilation or loading
and then an error. This can happen for some Intel vendor events, which cannot
be used.
This patch fixes this problem by forbidding BPF file patch containing '{', '}'
and ',', make sure flex consumes the leading '{', instead of matching it using
a BPF file path.
Tested result:
$ perf stat -e '{unc_p_clockticks,unc_p_power_state_occupancy.cores_c0}' -a -I 1000
invalid or unsupported event: '{unc_p_clockticks,unc_p_power_state_occupancy.cores_c0}'
Run 'perf list' for a list of valid events
(as expected, interperted as event)
$ perf stat -e 'aaa.c' -a -I 1000
ERROR: problems with path aaa.c: No such file or directory
(as expected, interpreted as BPF source)
$ perf stat -e 'aaa.ccc' -a -I 1000
invalid or unsupported event: 'aaa.ccc'
(as expected, interpreted as event)
$ perf stat -e '{aaa.c}' -a -I 1000
ERROR: problems with path aaa.c: No such file or directory
event syntax error: '{aaa.c}'
<SKIP>
(as expected, interpreted as BPF source)
$ perf stat -e '{cycles,aaa.c}' -a -I 1000
ERROR: problems with path aaa.c: No such file or directory
event syntax error: '{cycles,aaa.c}'
(as expected, interpreted as BPF source)
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reported-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1475900185-37967-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jiada Wang
Daniel Borkmann
Thomas Richter
Taeung Song
Masami Hiramatsu
Arnaldo Carvalho de Melo
Jin Yao
Adrian Hunter
Wang YanQing
Krister Johansen
Namhyung Kim
Maciej Debski
Rabin Vincent
Kan Liang
Jiri Olsa
Ravi Bangoria
Anton Blanchard
Wang Nan